Features:

• Compatible
  with DiSEqC 1.2 Receivers
• Indicating LED
  for Esy Trouble Shooting
• Manual Button
  for Easy Installation
• Compact,
  Powerful and Quiet
• For Dish up to
  1.2 M
• Goto X
  Function
• Azimuth &
  Elevation Angle Range
  1. The factory preset hardware
  limits for azimuth angle are from 75° East to 75° West. The
  azimuth range is sufficient for your multi-satellite programs
  selection.
  2. The motor's elevation angle range is from 0° to 70°, which
  meets most users' need.
• With this
  motor mount plus one dish, one
  
  DG6800 or
  
  DG7000 FTA recever as well as a set of our
  
  
  Digiwave Motorized Mount,
  you can then choose among all the different channels from
  various satellites. All you have to do is simply sit in front of
  the TV and enter the info for the satellite that you want to
  watch, then our H2H Motorized Mount will move the dish to the
  correct angles to allow viewing of a specific FTA satellite.
   

1. Aiming TRUE SOUTH.

Attaching the Antenna Dish to the Motor.
Make sure it is at the center of the mounting tube. Rotate the motor
together with the antenna towards TRUE SOUTH. You can find
the TRUE SOUTH via the magnetic variation table and a
compass that indicates the MAGNETIC SOUTH.

2. Setting Elevation Angle of the Motor.
    

Adjust the motor elevation angle via the
Inclinometer or the Elevation / Latitude scale on both sides
of the Motor.

3. Setting Angle of the Dish.

• Attach the Dish onto the motor. The
  centerline on the tube of the motor can help to mount the Dish
  on the center. Find the Declination Angle by the attached
  ANGLE TABLE.
• Set the Declination Angle by the scale on
  the antenna dish. The reading on the Dish scale should be:

30° - DECLINATION ANGLE

4. Drive the antenna east and west via the
   manual button on the bottom of the Motor or via Receiver
   to check if the reception arc is correct. If not, adjust the
   direction, elevation, and declination angle to find the best
   reception.

p.s. Please connect the Motor to the receiver via coaxial cable to get
the power. The Green LED will light on if the power from the
receiver is on.

II. Quick Installation (A receiver with Goto X Function is
recommended):

Rotate the motor together with the antenna towards TRUE SOUTH roughly first

1. Set Elevation Angle of the motor:
    

According to the Latitude of your
location, set the elevation angle of the motor. There is also a
Latitude scale on the other side of the motor.

2. Mount the Dish:

Mount the Dish onto the motor. The
centerline on the tube of the motor can help to mount the Dish on
the center.
Find the Declination Angle by the attached ANGLE TABLE.
Set the Declination Angle by the scale on the antenna dish. The
reading on the Dish scale should be:
30° - DECLINATION ANGLE Please refer to the drawing on
Page 2.

3. Drive the motor to the position for
   a favorite satellite:

According to your Longitude and the
position of the wanted satellite, drive the motor to the right
position. For example, a user in Paris (Longitude is 2.5°E) wants to
aim the Hot Bird (13°E). Just drive the motor to 10.5°E(=13-2.5) via
the manual button.
If the receiver has Goto X function, just input the longitude
and wanted satellite, the receiver can calculate and drive the motor
to right angle automatically.

4. Aim the Satellite:

Move the whole unit around the pole to
find the strongest signal from the wanted satellite.
Tighten everything and the installation is finished. It will take
about only 10 minutes.

The LED on the bottom of the Motor can show the
following information.

COLOR

STATUS

Green

On

  Power On; Standby Mode

Orange

Blink

  Receiving DiSEqC 1.2 Commands / Reset Mode

Orange

On

  Error Message: Over Current / Reach Hardware
Limits...

The Motor is designed for DiSEqC 1.2 Receiver.
The commands on the receivers might be different, but similar.
Please refer to the manual of the receiver.

1. Go East / West: Drive the dish to East /
   West.
2. Fine Tune East / West: Drive the dish East
   / West for one step.
3. Store nn: Store Satellites Position nn
   (01~60).
4. Goto nn: Drive Motor to Satellite Position
   nn (01~60).
5. East / West Limits: Set software East /
   West limits.
6. Limit Off: Disable the software limits.
    
7. Goto 0°: Drive the Motor to 0° as a
   reference point.
8. Re-synchronize / Shift:
    
   1. Drive the motor to a position by Goto
      command. For example, P03.
   2. Drive the motor East / West to a
      better position.
   3. Send Re-synchronize commands to the
      motor. The P03 will be shifted to the new position.
      All the other Satellite positions are also changed.
   4. If step a) is skipped, the P01 will be
      shifted to the new position.

9.    
Goto X Function

a.      
This function only works with receivers which have goto x function.
 

b.     
It can drive the motor to exact x.x° East or West in relative to the
0 position of the motor. ( For example, 15.2° East on the bottom of
the motor.)

c.      
Just input the longitude, some receivers can drive the antenna to
focus on the right Satellites automatically